Puspiekabe ar staigājošo grīdu

MENCI Schubbodenauflieger 92m³ SM136A

Ø Standard model, suitable for transporting dry bulk materials and palletized loads
Ø Chassis made of STEEL, prepared for Cargo Floor installation
Ø 1st axle as lift axle
Ø 3 SAF rigid axles, 9 tons each, with Ø 430 disc brakes
Ø Air suspension with manual raise/lower valve
Ø Support legs with universal foot (flat plate + half wheel)
Ø EBS WABCO braking system 2s/2c
Ø A.D.R. electrical system
Ø Pneumatic parking brake
Ø Wheel chocks and holders
Ø Side underrun protection
Ø 6 PVC mudguards
Ø 2 PVC toolboxes
Ø Internal dimensions:
Bcedpfjypa Hbex Admew
Length 13,542 mm - Front height 2,660 mm - Rear height 2,814 mm - Width 2,475 mm, volume 92 m³
Ø External dimensions:
Length 13,665 mm - Width 2,542 mm - Height above ground 4,000 mm, fifth wheel height 1,150 mm, gross weight 39,000 kg
Ø Moving floor system:
CF500 Cargo Floor (moving floor) with 21 aluminum slats, thickness 10 mm, standard type (smooth, longitudinally ribbed)
Ø Rear floor section made of stainless steel, approx. 300 mm long, about 4 mm thick
Ø Remote control in a waterproof control box
Ø Maximum pressure valve (225 bar) and high-pressure oil filter
Ø Slat movement: 200 mm/cycle
Ø Subframe:
Fully made from extruded aluminum profiles (crossmembers)
Moving floor supported longitudinally by aluminum tubes
Corrosion protection by polypropylene foils installed between aluminum and steel parts
Ø Front wall:
Aluminum profiles 600/30/3/2 mm with reinforced upper profile
Ø Front catwalk with 2 ladders for operating the side curtain
Ø Connection rail (with sockets) for braking system, lighting, and hydraulics
Ø Upper square reinforcement plates between front and side wall
Ø Mobile wall:
Made of aluminum profiles and curtain bead at the bottom, with reinforced strips for securing the curtain
Sliding bulkhead, suspended on trolleys with slide bearings on 2 tracks
Ø Side wall:
Made of aluminum profiles 600/30/3/2.5 mm, welded to the inner and outer contour
Upper surrounding profile with a rail for the movable partition
Ø Rear frame:
Made of aluminum profiles, with 2 doors made of aluminum profiles 600/30/3/2.5 mm, 50 mm peripheral door profile, double seal
Ø 4 aluminum hinges with galvanized pins (vertical), upright with handle
Fully bolted stainless-steel closure with vertical tube bar for each door
Ø Rotating upper rear cross member (one piece)
Ø Safety device for door release (pneumatically operated)
Ø Roof:
4 removable cross members
Curtain fastening straps, vertical with 4 side tensioning straps
2 tension belts over the entire length
Ø Tarpaulin 900 g/m²
Fastening of the right-side tarpaulin with rivets along the surrounding profile
Ø Chassis color: SILVER GREY MENCI
Ø Body color: MENCI SILVER GREY
Ø Tarpaulin color: RAL 9006
Ø Standard accessories:
4 safety hooks for tarpaulin
Holder for shovel, broom, and rake
Pressure gauge for weight control (63 mm diameter) in the moving floor’s control box
Compressed air gun connection on the left rear side
Prepared for tarp roller (floor tarp) at the rear
Rear foldable guard for tail lights
Ø Additional special equipment:
6 SPEEDLINE light alloy rims, 385/65 R 22.5, offset 120
Ø RADIO REMOTE CONTROL

All information without guarantee!

Sludinājums tika tulkots automātiski, tāpēc tajā varētu būt dažas tulkošanas kļūdas.