Atvērta puspiekabe ar tentu

KRONE SDP 27*Mega*BPW*LiftA*StaplerH

Distance from kingpin to center of support device: 2,267 mm
Fifth wheel height unladen: 980 mm
Double-T longitudinal and center beams, as well as crossbeams and outriggers are welded
Outer frame with
Multilock outer frame, universal load securing options every 100 mm
Iodpjzr Dkzsfx Aqcetl
Front overall height: 80 mm (incl. floor and fifth wheel plate)
2" kingpin (corner dimension: 2,040 mm)
Rear underrun protection device according to EC directive,
for cargo box length: 13,620 mm i. L.
for cargo box width 2,480 mm i. L.
3 axles with a load-bearing capacity of 9,000 kg each
Aggregate distance = 7,900 mm
Wheelbase: 1,310 / 1,310 mm
with center alignment
BPW axles, 19.5", with air suspension (total travel 260 mm)
and disc brake (ET 120)
Brake disc with 370 mm diameter
Tire size 6-fold, 435/50 R 19.5
Tread depths:
5/4 mm
4/12 mm
9/6 mm
with lifting and lowering device, incl. automatic
restoration of driving height
Load-dependent, fully automatic, electronic
lift axle control for 1st axle
Manual function on control console for forced lifting
(= starting aid according to Directive 97/27/EC) and forced lowering
Preparation of the lift/trailing axle(s) for operation
from the tractor unit (without tractor unit installation),
according to the selected plug connection(s) for light,
for control via
Note: The vehicle does not operate in the
BO power circuit when the 1st axle is lifted! The lift axle may only be used as a starting aid in accordance with
Directive 97/27/EC!
Caution: Reduced ground clearance in the area of the lift axle!
Through-loading height restricted by pallet stop
Cargo box width in the area of the pallet stop
reduced to: 2,460 mm i. L.
Delivery and installation of a rear forklift bracket, suitable
for Palfinger piggyback forklift (incl. forklift pockets, underrun protection according to ECE-R58 and 2 counter brackets for securing chains on the outside)
Tire size piggyback forklift max.: 23"
Design of the mounting bracket: spar bracket
Dimensions of the support spars: 100 x 100 x 10 x 1500 mm
Dimensions of the forklift pockets: 200x100x5x1200 mm
Center distance of the forklift pockets: 380 mm
Width of the folded-down underrun protection: 1340 mm
Forklift pockets flush with the end cross member at the rear.
Rear socket: 15-pole DIN ISO 12098
Uneven load distribution!
Type: BO 13620
30 mm thick, waterproof floor panel, cut edges
sealed all around, planar, waterproof bonding
between chassis and floor panel with permanently elastic high-performance adhesive. Strength according to DIN EN 283, for floor loads up to max. 7,000 kg forklift axle load.
Tear plate embedded in the floor panel at the rear (4x450mm)
Type: AB 13620 AGG Dimensions 13,620 mm i. L. x width i. L.
see spars
LM universal outer spars, continuous, for accommodating
sliding tarpaulin and sliding spars
Edscha sliding tarpaulin (175) with plastic joints,
overall height 175 mm, inclination 0 mm, designed for the
transport of grid boxes according to DIN 15155
Height i. L. lower edge of outer spar at the front side: 2,860 mm
Height i. L. lower edge of outer spar at the rear side: 2,860 mm
Height i. L. lower edge of transverse spar in the middle: 3,000 mm
Through-loading height in the rear portal: 2,845 mm
unladen overall vehicle height at the highest point approx. 4095 mm
hydraulic lift roof with 500 mm total lift,
can be raised separately at 4 corner spars
Overall height at the front, lowered from the highest driving height (basic position) by
150 mm (in 50 mm increments), reduced roof lift: 350

Sludinājums tika automātiski tulkots. Iespējamas tulkošanas kļūdas.