Trīspusējs kravas pašizgāzējs

MAN TGS 26:480 6x4 EURO5 ATLAS 240.2E-A4 3-S-Kipper

MAN TGS 26.480 6x4 BB with SCHWARZMÜLLER 3-way tipper with demountable ATLAS 240.2E-A4 crane and radio remote control.
German vehicle, 1st owner.

Equipment:
ZF 16-speed manual gearbox with Intarder

Special equipment:
Car phone antenna
Comfort driver's seat, air-suspended and heated, with lumbar support and shoulder adjustment
Flame-start system
Transmission: 16-speed, type ZF 16S2310
Fuel tank: Aluminium - 400 l diesel
60 l AdBlue tank
1-cylinder air compressor, 360 cc with Air Pressure Management (APM)
Heated air dryer
Retarder / Intarder
Exterior sun visor
Radio
12V and 24V sockets in cab
Axle configuration: 6x4
Starting/front mirror
24V / 7-pin trailer socket
ABS trailer socket
Anti-slip regulation (ASR)
Audio system: MAN Media Truck Advanced 12V radio with navigation system preparation
Exterior mirrors electrically adjustable and heated, wide angle mirror heated
On-board computer MAN-Tronic
Kerb mirror right
Rear axle differential lock
Electronic braking system MAN-Brakematic
EURO 6 engine
Suspension: leaf/air
Electric windows
Tinted windscreen
Alternator 28V 80A
Automatic air conditioning
Multifunction steering wheel
Raised air intake
Engine: 12.4 l, 353 kW diesel
Engine compartment encapsulation
Rear side windows tinted
Seat cover/upholstery: comfort quality
Side window sun blind + driver's door
Rear axle stabilizer
Front axle stabilizer
Viscous fan
All-round warning beacons
PTO NH/1C
Intarder
Additional construction vehicle step
Rear axle differential lock
Electronic braking system MAN-Brakematic
Cab type: M (medium-length)

ATLAS CRANE Type 240.2E-A4
1.93m = 11.2 t
4.51m = 4.78 t
6.41m = 3.22 t
8.31m = 2.4 t
10.31m = 1.88 t
12.31m = 1.56 t
14.30m = 1.26 t
Radio remote control
Palfinger demounting console
High seat with holder for remote control
SCHWARZMÜLLER 3-way tipper body

Dimensions
Internal length approx. 6,300 mm
Internal width approx. 2,420 mm
Total width 2,550 mm
Subframe
Continuous longitudinal beams with tipping cylinder mounts and tipping arms
Low body height approx. 440 mm
Plug lock for tipper body with cross protection
Hedowtkipjpfx Ahpsw
Body support and soundproofing
Reinforced subframe and reinforced end plate for Atlas 240.2E-A4 crane, removable rear section, welding of the two supplied mounting plates for the removable rear section, without crane body
High-pressure hydraulic tipping system
20 t tipping cylinder for 3-way tipping, with safety cable
Tipping angle to the rear approx. 40 degrees
Load-sensing pump mounting
Oil tank installation (by crane supplier)
Pneumatic tipping valve with overpressure valve
Pneumatic 3-way switching valve for tipping crane
2-pipe trailer tipping connection with pneumatic 3-way switching valve, incl. DN16 fitting
Tipping platform
Welded all-steel construction with 5 mm fine-grain stainless steel floor plate
10 pairs of rotating lashing eyes, distributed: first pair approx. 400 mm from the front wall, approx. 600 mm; width between the lashing eyes 2,320 mm
Lashing bars with lashing straps on both sides under the tipper body
Fixed front wall made of 4 mm steel, approx. 980 mm high
Cab guard with lashing eyes can be fitted
2 steps on the outer front wall (left) – allows access to the cab
2 steps on the inner front wall (left).
Continuous one-piece side walls made of reinforced aluminium hollow profiles (60/4/3 mm), approx. 980 mm high

Sludinājums tika automātiski tulkots. Iespējamas tulkošanas kļūdas.