Platformas piekabe

FLIEGL Tandem-Plattformanhänger Bau TPS 118 Bau

Customized Transport Solution
Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs.

Chassis: Center-axle trailer
Fine-grained steel welded construction
Outer frame slightly angled, new design with "Load-Lock profile" for tie-down straps
3 pairs of lashing eyes outside in the floor, each 5 tons
1 at the front in the corners, 1 in front of and 1 in the rear incline at the back
6 pairs of lashing eyes outside in the floor/outer frame, each 5 tons
Gearbox support leg at the front
Dsdozcqpaepfx Abnsuu
Rear support, foldable
2 wheel chocks with holder
Aluminum side impact protection
Steel underrun protection, galvanized
Splash guards at the rear covering the entire width (not in combination with forklift mount)
Quarter panel fenders
1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable
Coupling device: Center-axle trailer
Drawbar with tested 40 mm drawbar eye
Drawbar height-adjustable via spindle, max. adjustment range 300 mm
Axles + Suspension
GFA or BPW axles, at the manufacturer's choice, with tapered roller bearing and S-cam brake
"Axle/chassis laser-aligned" - reduces tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (lever compensation)
Braking System
2-line compressed air brake system
Color-coded line routing for easy servicing
Hand-spindle parking brake
2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle
24 volt ABS and ALB, with ABS connector at the front, with connecting cable
Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
Wheels and Tires
235/75 R17.5, manufacturer's choice
Steel rims, factory silver
Electrical System
24 volt, multi-chamber lights, yellow LED lighting on the sides
2 white position lights at the front, in LED
2 white/red marker lights at the rear
2 x 7-pole fail-safe plugs at the front, with connecting cable
Floor
Steel/diamond plate floor for high point load capacity
Note: Slight floor waviness due to welding distortion is possible!
Platform length approx. 6,200 mm
Rear incline to approx. 900 mm
Front wall / corner posts at the front
25 mm aluminum hollow profile, 400 mm high
Side walls
25 mm aluminum hollow profile, 400 mm high, foldable and removable
Rear wall / corner posts at the rear
1 pair of steel uprights attached to the frame, with brackets for locking the access ramps, access width approx. 2,430 mm
Access Ramps
Steel ramps 2,300 mm long, 510 mm wide, laterally movable
With handrail on the ramps
Covered with wood (tip area with steel/diamond plate)
With gas spring for one-person operation
Operating Instructions
The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and following behavior possible due to incorrect load distribution)
Country of Registration / Signs
Germany
With DEKRA inspection and certificate (according to §13 EG - FGV)
24/7 service hotline
Prepared for single-row license plate holder
Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear
Paintwork
Frame DB 7350 Novagrau
"10-year warranty against rusting"
Front wall Aluminum
Side wall Aluminum, anodized
Access ramps Hot-dip galvanized

Customized Transport Solution

Sludinājums tika automātiski tulkots. Iespējamas tulkošanas kļūdas.