Puspiekabe

FAYMONVILLE Prefamax Innenlader 3 x LASI

You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Below is an excerpt of the equipment. Complete equipment list available upon request.

GOOSENECK: Gooseneck designed as a loading platform with a surface made of aluminum tear-plate sheeting. Hydraulic lifting drawbar, adjustable by approximately -280/+250 mm. Two kingpin positions at approximately 2,300 mm and 2,000 mm. For semi-trailer: 4 x 2, 6 x 2, or 6 x 4. - 2-inch kingpin. - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN). - ASPÖCK-UNIBOX on the front connection bar with 24N, 24S, and 15-pin sockets. - 24N connection according to ISO-1185. - 24S connection according to ISO-3731. - 15-pin connection according to ISO-12098. - Yellow-red air couplings on the front connection bar. - Lighting for the operation of the gooseneck, suspension, and hydraulic locking, with on/off switch. - Brackets for hanging the supply lines on the front of the gooseneck. - Operation of all work lights in the gooseneck area via on/off switches on the gooseneck (operation of the work lights from the semi-trailer is not possible in this case).

Gsdpfxjz N Nx De Aa Uobu
LOADING PLATFORM: Loading platform, length approximately 9,500 mm, with angle profiles attached underneath to accommodate the load pallets (distance from kingpin to center of axle unit approximately 8,000 mm). - BPW axle stub, with drum brakes and single-wheel suspension, hydraulic axle equalization with lifting and lowering mechanism. - Lowering lock on the axles in case of suspension air spring failure, designed for a maximum pallet height of 150 mm. - 385/65 R 22.5 (M+S) - Manufacturer of our choice. - Mechanical drop-side supports for approximately 48,000 kg of support load. - Access ladder mounted on the front right with 2 retractable handrails. - Removable full fender on both sides in front of the axle unit. - WABCO Roll Stability Support (RSS). - 9 pairs of lashing rings on the longitudinal beams (LC 6,300 daN). - Grid flooring support on the longitudinal beams, at the same height between the guide rails of the load securing system. - The first and last axle on the left and right can be manually lifted. - Storage box on the left and right behind the axle unit, protected from splashing water. - Beveled rear end for easier insertion of the load pallet. - Eyelets attached to the rear crossmember for mechanical locking. - Rear door with cross bracing, hinged on the left and hydraulically locked on the right, can be locked horizontally at 90°, 105°, and 270°. - Underrun protection that can be folded upwards for the transport of up to 4 empty standard pallets. - License plate with holder including lighting on the rear door. - One 7-pin socket on the rear crossmember. - Electro-hydraulic unit for operating the hydraulic functions (without installation in the semi-trailer). - TPMS tire pressure monitoring sensors installed in all wheels. - TPMS tire pressure monitoring system according to ECE R 141. - Indicator lights to display the nominal ride height in the vehicle control area. - 1 odometer mounted on the left. - 2 axle load gauges mounted on the left side, including axle load diagram. - 2 rubber buffers in the front of the loading platform as a stop for the load pallet. - Hydraulic preparation including control for the installation of 4 pairs of our hydraulic load securing systems. - 1 spare wheel holder on the right in the direction of travel. - Acoustic warning signal

Sludinājums tika automātiski tulkots. Iespējamas tulkošanas kļūdas.