Zema kravnes piekabeMÜLLER-MITTELTAL
14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Zema kravnes piekabe
MÜLLER-MITTELTAL
14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
fiksēta cena bez PVN
29 900 €
(35 581 € bruto)
Izgatavošanas gads
2025
Stāvoklis
Jauns
Atrašanās vieta
Egestorf 

Rādīt attēlus
Rādīt karti
Pamatdati
Cena un atrašanās vieta
fiksēta cena bez PVN
29 900 €
(35 581 € bruto)
- Pārdevēja atrašanās vieta:
- Eichenstich 12, 21272 Egestorf, Vācija

Zvanīt
Tehniskā informācija
- Maksimālā kravnesība:
- 10 800 kg
- Kopējais svars:
- 14 400 kg
- Asu konfigurācija:
- 2 asis
- Krautuves garums:
- 6 270 mm
- Iekraušanas vietas platums:
- 2 470 mm
Piedāvājuma informācija
- Ieraksta ID:
- A204-85-575
- Atsauces Nr.:
- 62471
- Pēdējoreiz atjaunots:
- 21.1.2461062
Apraksts
* ETÜ-TA-R 14.4:
----Brakes:
* EBS brake system
* Emergency release device for spring brake cylinders
* Drum brakes
----Axles:
* 2 x 7 t Gigant axles
----Suspension:
* Parabolic springs with compensating unit
----Drawbar / Flange Drawbar Eye:
* Drawbar height-adjustable by 300 mm
* Drawbar extension by 250 mm to a total length of 2,250 mm
----Electrics / Lighting:
* Tire pressure monitoring with display option in the truck via EBS signal – without installation required on truck side
* 15-pin electrical connector
* LED lighting system 12 / 24 V
* EBS multi-voltage system for towing vehicles with 12 and 24 V electrics
----General Attachments:
* Front support winch
* External folding supports at the rear
* Plastic toolbox approx. 858 x 500 x 500 mm on the right front exterior of the front wall
* Side underrun protection
* Plastic quarter mudguards
----Low Loader Platform:
* 50 mm softwood floor
* Provision in front of the front wall for retrofitting container locks
* Bolted 400 mm smooth sheet front wall
* Bolted rear stanchions
* Drop sides with spring assists
----Load Securing:
Dodpfx Asxvgrieaxscc
* Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm
* Installation of 3 t recessed lashing rings possible every 600 mm
* In each front and rear corner, 1 x 6.3 t lashing point
* Various holes in the front and rear crossmember for 1.2 t lashing options
----Ramps:
* One-piece hydraulic grating drive-on ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm clearance)
* Hydraulic flow divider in the trailer (for truck hydraulic output above 40 l/min up to max. 140 l/min)
----Paintwork:
* Chassis, drawbar, front wall, mechanical drop supports, and drive-on ramps hot-dip galvanized
* Axles, springs, air tanks, front support winch, and flange drawbar eye painted in a black tone
* Drop sides painted RAL 2011 deep orange
* Side panels available in a RAL color of your choice for an additional charge
----Information:
* New vehicle with manufacturer’s warranty
* Errors and prior sale excepted
----Delivery Time:
* Available immediately ex Egestorf
Sludinājums tika tulkots automātiski, tāpēc tajā varētu būt dažas tulkošanas kļūdas.
----Brakes:
* EBS brake system
* Emergency release device for spring brake cylinders
* Drum brakes
----Axles:
* 2 x 7 t Gigant axles
----Suspension:
* Parabolic springs with compensating unit
----Drawbar / Flange Drawbar Eye:
* Drawbar height-adjustable by 300 mm
* Drawbar extension by 250 mm to a total length of 2,250 mm
----Electrics / Lighting:
* Tire pressure monitoring with display option in the truck via EBS signal – without installation required on truck side
* 15-pin electrical connector
* LED lighting system 12 / 24 V
* EBS multi-voltage system for towing vehicles with 12 and 24 V electrics
----General Attachments:
* Front support winch
* External folding supports at the rear
* Plastic toolbox approx. 858 x 500 x 500 mm on the right front exterior of the front wall
* Side underrun protection
* Plastic quarter mudguards
----Low Loader Platform:
* 50 mm softwood floor
* Provision in front of the front wall for retrofitting container locks
* Bolted 400 mm smooth sheet front wall
* Bolted rear stanchions
* Drop sides with spring assists
----Load Securing:
Dodpfx Asxvgrieaxscc
* Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm
* Installation of 3 t recessed lashing rings possible every 600 mm
* In each front and rear corner, 1 x 6.3 t lashing point
* Various holes in the front and rear crossmember for 1.2 t lashing options
----Ramps:
* One-piece hydraulic grating drive-on ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm clearance)
* Hydraulic flow divider in the trailer (for truck hydraulic output above 40 l/min up to max. 140 l/min)
----Paintwork:
* Chassis, drawbar, front wall, mechanical drop supports, and drive-on ramps hot-dip galvanized
* Axles, springs, air tanks, front support winch, and flange drawbar eye painted in a black tone
* Drop sides painted RAL 2011 deep orange
* Side panels available in a RAL color of your choice for an additional charge
----Information:
* New vehicle with manufacturer’s warranty
* Errors and prior sale excepted
----Delivery Time:
* Available immediately ex Egestorf
Sludinājums tika tulkots automātiski, tāpēc tajā varētu būt dažas tulkošanas kļūdas.
Piegādātājs
Piezīme: Reģistrējieties bez maksas vai piesakieties, lai iegūtu visu informāciju.
Reģistrēts kopš: 2001
Iesniegt pieprasījumu
Tālrunis & Fakss
+49 40 33... sludinājumi
Šie sludinājumi varētu arī jūs ieinteresēt.
Mazā sludinājuma
Egestorf
1 011 km
Piekabe ar darba platformu
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Mazā sludinājuma
Egestorf
1 012 km
Zema kravnes piekabe
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Mazā sludinājuma
Egestorf
1 012 km
Piekabe ar darba platformu
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
MÜLLER-MITTELTAL14,4 to, Tand - Plateau- Tieflader, hydr. Rampen
Jūsu sludinājums ir veiksmīgi dzēsts
Radās kļūda






























































