Maināmas šasijas

Hangler LKW Tieflade Liftmaster Aufbau für 3 Achs LKW Fahrgestell zum Transport von Arbeitsbühnen

Additional Information

Frame
Steel welded construction made of fine-grain steel, hot-dip galvanized, flat platform without edge extension,
the loading area slopes downwards by approx. 8° towards the rear axle. Longitudinal beams made of steel profiles,
steel frame hot-dip galvanized, with a stainless steel plate on the bend as a cable guide, flush with the floor. For trucks with
wheelbase: 2nd axle 5,100 mm / 2nd to 3rd axle 1,350 mm

Tow Hitch
Tow hitch ball head D24.8: (height from ground to top approx. 480 mm), towing capacity 2,800 kg,
including assembly and electrical system with 7-pin socket

Accessories / Modifications
2 holders for wheel chocks, aluminum side impact protection, foldable - taken over from the truck!
Steel underrun protection, quarter-shell fenders with mud flaps - taken over from the truck!
Storage Box
Plastic toolbox, with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included).
1 holder for 3 pieces of gasoline canisters
1 stainless steel storage box, w=600/h=400/d=500 mm, with polished door, including lock, contains control valve and electro-hydraulic
pump unit. Control box with all-around door seal and sealing sleeves on the back (splash-proof according to technical possibilities)

Electrical System
Adaptation of the existing tail lights, 2 additional LED work lights, recessed in the front panel, switched via parking lights with a switch on the front panel on the left, 1 LED work light
at the rear, with integrated reversing camera including color flat-screen monitor, screen with suction cup holder and power supply via 24 volts,
voltage divider 24/12V, 1 7-pin 12V socket = adapter
Floor
Lhjdpfxji Riyts An Ieh
Mega Grip made of interlocking, galvanized grating, steel grating 50/4 including with mesh size 50 mm. Top surface with anti-slip interlocking,
continuously laid across the entire main frame platform
Tie-Down Eyes
12 pairs of tie-down eyes attached to the outer frame, freely swiveling - 10 tons each, 1 at the very front and the last at the very back. 1 tie-down eye at the very back in the middle for attaching the
winch cable
12 tie-down eyes recessed in the middle of the floor, 5 tons each (not in the rear slope)
Front Wall
Front wall made of steel sheet, height 1,500 mm. Fixed with corner pillars at the height of the front wall. Each with 2 x 12 tie-down loops for lashing chains mounted on the left and right on the front wall.

Winch
Electric winch, 24 volts, pulling force approx. 6350 kg, mounted in the middle at the front wall (recessed with loading bridge), operated with a remote control, cable length min. 35 m x 9.5 mm, with cable guide,
with cable pressure plate, including overload protection, cable free-running clutch, hand switch with approx. 5 m control lever, acceptance of the winch, civil engineer test report, test book, operating instructions.

Ramps
Length 3,500 mm - 2-piece (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also when loading ramps), electro-hydraulically foldable and laterally adjustable - including electro-hydraulic pump unit. Ramp angle approx. 8° with lowered rear axle.
Ramp support made of steel grating, hot-dip galvanized (like the floor of the loading bridge), with anti-slip interlocking. Ramps can be pushed together to approx. 170 mm, ramp extension hydraulic. Ramp prepared for operation on loading ramp with full load capacity. Ramp locking with 2 tension straps.
Ramp tip offset (nose min. 150 mm) for supporting on loading ramps.
Labeling

Sludinājums tika automātiski tulkots. Iespējamas tulkošanas kļūdas.